Get Answers from our
Community of Computer Experts

How do i get a netgear expander in a connected network does not accept the security key


Asked by
Keijo Ahola
2017/09/14 07:05
0 Like It
Forget the whole thing
Operating System:
Windows 8.1
Answer this question
best answer

 
Answered by
Christian Velasco
2017/09/14 09:59
Moikka Keijo,

Thank you for posting my concerns here.

I'm sorry about the problem you are experiencing.

Could you share additional information about the problem, including the product name?

Screenshots be helpful as well.

Looking forward to hearing from you.

With respect,

Christian


Comments
Commented by Keijo Ahola
2017-09-14 10:46:58
Yes I put the name of the product in the past it was the NETGEAR WiFi Range Extender 300Mbps Expander question was how do I get it measures the combined network and when does it concern the supplied security key 4GN26C5A00284 this I have tried many times.

Cancel
 
Answered by
Lokesh Yadav
2017/11/05 13:00

0 votes

0
0
Hi Keijo,

Please use the below steps to resolve the issue. If you have a NETGEAR WiFi Extender with an Ethernet port (EX6100, for example):
  1. Use a computer to connect to NETGEAR WiFi Extender via Ethernet cable.
  2. Login to the web user interface of your NETGEAR WiFi Extender using http://myWiFiext.net.
    You will be prompted to enter a username and password.
    Default login credentials are:
    • Username: admin
    • Password: password
      Note: Username and password are case sensitive.
  3. Once you have successfully logged in, go to Setup > Wireless Settings.
  4. Check the value in the Password (Network Key) field under Security Options.
    If the password is not same as your Access Point (AP) password, change it so it matches your Access Point password.
  5. Click Apply. (Extender and AP password need to match)
  6. Reconnect your Wi-Fi devices to the NETGEAR WiFi Extender using either the WPS button or manual connection.

If you have a NETGEAR WiFi Extender without an Ethernet port (WN1000RP, for example):
  1. Reset your NETGEAR WiFi Extender back to factory default settings.
    To do this, press and hold the Factory Settings button on the side panel for 7 seconds.
  2. Connect via Wi-Fi to your NETGEAR WiFi extender
  3. Login to the web user interface of your NETGEAR WiFi Extender using http://myWiFiext.net.
    You will be prompted to enter a username and password.
    Default login credentials are:
    • Username: admin
    • Password: password
    Note: Username and password are case sensitive.
  4. Walk through the setup wizard to setup your connection to your Access Point. (Do not use WPS when reconnecting to the Access Point)
  5. Reconnect your Wi-Fi devices to your NETGEAR WiFi Extender using either the WPS button or manual connection.
Regards,
Lokesh
Cancel
Cancel

Welcome to Reviversoft Answers
ReviverSoft Answers is a place to ask any question you have about your computer and have it answered by the expert community.
Post your question
Ask your question to the community now
Similar questions
When I connect an external microphone to the jack, it is not working. I can see it in the "Sound" tab, but the levels is very low. I have tried with several microphones.
VIEW ANSWERS
40
Show full question
mein pc ist put mochte nun reviversoft auf mein laptop registriren wie geht das und was muß ich tun
VIEW ANSWERS
19
Show full question
I kept getting the blue screen with Driver Power State Failure error message and then my computer would restart. I found your product and it did not happen any more. I just purchased an anti-virus (kaspersky) and now it is doing it again. It is so frustrating. My computer is only 6 months old. It is a Asus desktop.
VIEW ANSWERS
8
Show full question
Having trouble with your PC?
Complete a free PC scan using Driver Reviver now.
Download
Start Free Scan
Copyright © 2024 Corel Corporation. All rights reserved. Terms Of Use | Privacy | Cookies
follow us